How to Install Formica Countertops

How to Install Formica Countertops

How to Install Formica Countertops –¬†Formica is laminated from home, it is used more often use for kitchen counters and wall decor. The laminate is easy to clean and relatively durable, though, as it is plastic, it can melt if exposed to excessive heat. The laminate comes in many styles and can be cut using ordinary saws, making your installation a great do it yourself design.

How to Install Formica Countertops

Revive your kitchen with newly laminated worktops. They are available in a variety of colors, shades, textures, and patterns to ensure that you find a look that suits your style. And because they are relatively easy to install, you will save money on installation costs.

 

Before you buy

First, measure the depth of your cabinet. The standard depth is 23 3/4 inches. To check the depth, measure from the back wall for accuracy. If you want a bit of projection-the standard is 1 1/4 to 1 1/2 inches-add that to size.

Then measure your current splash height. Your new cover will need to clear all plugs and window adjustment. You must also cover unfinished areas unless you intend to refinish and repaint the area of the wall.

Finally, check if your walls are fairly straight with a square and a level. A little reverence is good. You can trim the countertop to fit. Some cases may require a custom Top. Also, make sure the walls meet at 90 degrees.

 

Install Laminated Worktops

Step 1

Remove drawers and closet doors. Turn off the power in the kitchen. Remove the waste collector and drain, and disconnect the water source and drain lines to the area. Remove the heatsink supports and remove the heatsink.

Step 2

Cut the sealant along the dashboard. Remove the corner screws and screws under the cover that hold them to the cabinets. In some cases, you will also have to cut the glue. Also, check to make sure your dishwasher is not attached to the bottom of the countertop.

Step 3

Pull a little on the old top; He should be in a play. You can use the old countertop as a mold to cut your new laminate countertop.

Step 4

Cut the new countertop to the length of the back using a thin-tooth saw blade. Archive The flat end, archiving in one Direction.

Step 5

Make sure the cabinet drawers clean the front edge of your new laminate countertop. If not, you can place accumulation strips under the countertop. Some laminates come with these strips. You can also make your own with 1 by 2 pieces of wood. Keep them in the cabinets, glue the pilot holes and fasten the strips with the short wood nails or the screws on every 2 feet, remaining 2 inches from the ends.

Step 6

Now, check the setting. Run a piece of tape along the top of the board so that it is marked later and place the countertop in place. Try to set the mitered corner as tight as possible and tighten the miter screws.

Step 7

You’ll probably notice a hole along the wall. Attach a compass to the width of the larger space and mark a line along the back edge. Take the new countertop and sand to the line with a belt sander. File all burrs, filing in one direction away from surfaces. Re-check adjustment, making any additional adjustments.

Step 8

Add the return sneezes where the counter finds the walls. Add the final finish and the end where the counter finds the walls and where it leans. If you have an iron end to cover exposed edges, attach the workpiece, hold a damp cloth on it and press it with an iron. Edges can be trimmed and retouched with a file.

Step 9

If you need to make a cut for the top of the sink and the cooktop, use the old laminate cover as a guide. If you are installing a new selector or top track, use the model that comes with the box. If your sink or the top of the range did not come with a mold, set the item upside down on the new countertop. Center and trace the contour. Draw a 1/2 inch band around the edge inside the contour.

Step 10

The Court will be online from 1/2 inch inside the edge of the model. Place masking tape around the edges to protect the countertop. Make a few holes starting 1/2 inch at each corner of your guide. Cut the piece thoroughly, taking care not to drop it. File the rough edges until they are smooth, so you do not cut your hand or let chips install the lid of the stove or sink.

Step 11

Before putting your new laminated countertop in base cabinets, you can add additional support near the borders, especially along the coasts.

Step 12

To ensure your new countertop laminate, drill the accumulation or add brackets inside of your cabinets. Place them just below the top of the strips. Place the countertop, starting with the longest part. Apply the recommended adhesive square and adjust miter gauge pins. Hit the seam with a mallet and scrap wood to get it even.

Step 13

Tighten the screws until the miter end, avoiding breaking the substrate. Wipe off any excess glue. Use #8 head screws to attach the top to the brackets.

Step 14

Finish adjusting the sink and stove, apply silicone around the edges and the back wall. After connecting the pipes, it’s time to install the drawers and cabinet doors.

Step 15

Back and admire your updated kitchen.

View Comments

Leave a Reply

Your email address will not be published. Required fields are marked *